% cd '#ec'; for(i in *){echo $i '=' `{cat $i}}
bcm2708.boardrev = 0xf
bcm2708.serial = 0x43eccb5
bcm2708_fb.fbheight = 416
bcm2708_fb.fbswap = 1
bcm2708_fb.fbwidth = 656
dma.dmachans = 0x7f35
nobootprompt = local!/dev/sdM0/fs -m128
nvram = #S/sdM0/nvram
readparts = 1
sdhci-bcm2708.emmc_clock_fr = 250000000
smsc95xx.macaddr = B8:27:EB:3E:CC:B5
sysname = p901
user = tdempsey
vc_mem.mem_base = 0x1ec00000
vc_mem.mem_size = 0x20000000

% cat '#'P/archctl
cat: can't open #P/archctl: '#P/archctl' file does not exist

% cat '#'P/irqalloc
cat: can't open #P/irqalloc: '#P/irqalloc' file does not exist

% cat '#'P/ioalloc
cat: can't open #P/ioalloc: '#P/ioalloc' file does not exist

% cat '#'c/config
dev
	root
	cons
	env
	pipe
	proc
	mnt
	srv
	shr
	dup
	arch
	ssl
	tls
	cap
	fs
	ip		arp chandial ip ipv6 ipaux iproute netlog nullmedium pktmedium ptclbsum inferno
	draw	screen swcursor
	mouse	mouse
	uart
	gpio
	sd
	usb

link
	ethermedium
	archbcm
	usbdwc

ip
	tcp
	udp
	ipifc
	icmp
	icmp6
	ipmux
	il

misc
	uartmini
	sdmmc	emmc
	dma
	vcore
	vfp3	coproc

port
	int cpuserver = 1;

bootdir
	/$objtype/bin/paqfs
	/$objtype/bin/auth/factotum
	bootfs.paq
	boot

% cat '#'c/swap
466587648 memory
4096 pagesize
34174 kernel
39985/79739 user
0/341739 swap
3408704/131042933 kernel malloc
2097184/16777216 kernel draw

% cat '#'c/sysstat
          0   392389798   805472140    18720592      902470           0           0        1278          58           0 

% awk /^Plan 9/{p=1} /^init: starting/{exit} {if(p)print} '#'c/kmesg
Plan 9 from Bell Labs
firmware: rev 1417627772
cpu0: 700MHz ARM1176JZF-S
fp: 16 registers,  simd
fp: arm arch VFPv2; rev 5
eMMC external clock 250 Mhz
448M memory: 137M kernel data, 311M user, 1646M swap
hjfs: fs is /dev/sdM0/fs
usbotg: ep4.2 error intr 00000082
nusb/kb: hid: /dev/usb/ep4.2: read: i/o error


% pci -v
Can't cd #$/pci: unknown device in # filename

% aux/cpuid
aux/cpuid: this information is classified

% aux/icanhasmsi
open /dev/pci: '/dev/pci' file does not exist

% aux/pcmcia
pcmcia: opening #y/pcm0attr: unknown device in # filename

% cat '#'u/usb/ctl
ep1.0 enabled control rw speed high maxpkt 64 pollival 0 samplesz 0 hz 0 hub 0 port 0 busy
roothub csp 0x000009 ports 1 dwcotg
ep2.0 enabled control rw speed high maxpkt 64 pollival 0 samplesz 0 hz 0 hub 1 port 1 busy
hub csp 0x020009 ports 3 none <nil> dwcotg
ep3.0 enabled control rw speed high maxpkt 64 pollival 0 samplesz 0 hz 0 hub 2 port 1 idle
ep4.0 enabled control rw speed full maxpkt 64 pollival 0 samplesz 0 hz 0 hub 2 port 3 busy
ep3.1 enabled bulk r speed high maxpkt 512 pollival 0 samplesz 0 hz 0 hub 2 port 1 busy
ep3.2 enabled bulk w speed high maxpkt 512 pollival 0 samplesz 0 hz 0 hub 2 port 1 busy
ep4.1 enabled interrupt r speed full maxpkt 64 pollival 8 samplesz 0 hz 0 hub 2 port 3 busy
ep4.2 enabled interrupt r speed full maxpkt 64 pollival 1 samplesz 0 hz 0 hub 2 port 3 busy

% cat '#'S/sdctl
sdM mmc 1 units

% cat '#'S/sdM0/ctl
inquiry Arasan eMMC SD Host Controller 02 Version 99
rca 0007 ocr c0ff8000
cid 2750485344333247307c00b9a200c400 csd 400e00325b590000ef177f800a400000
geometry 62676992 512
part data 0 62676992
part dos 63 1028160
part plan9 1028160 62669565
part 9fat 1028160 1232960
part nvram 1232960 1232961
part fs 1232961 62669565

% cat '#'v/vgactl
cat: can't open #v/vgactl: unknown device in # filename

@{rfork n; aux/realemu; aux/vga -p}
aux/realemu: open iob: '#P/iob' file does not exist
mkvbe: '/dev/realmode' file does not exist
aux/vga: controller not in /lib/vgadb, not vesa
aux/vga: devopen(#P/iob, 2): '#P/iob' file does not exist
% xd -x1 '#'r/nvram
xd: can't open #r/nvram

% cat '#'A/audiostat
cat: can't open #A/audiostat: unknown device in # filename

% cat '#'A/volume
cat: can't open #A/volume: unknown device in # filename

% cat /mnt/apm/ctl
cat: can't open /mnt/apm/ctl: '/mnt/apm/ctl' does not exist